An 2011 Nissan Altima serpentine belt replacement too small will bind the pulleys while an 11 Nissan Altima serpentine belt replacement too large will just fall off. The 0885 is the outside lenght which is 88. Once the 11 Nissan Altima serpentine belt replacement is around the pulleys, allow the 2011 Nissan Altima serpentine belt replacement to hang freely at the bottom of the engine. The repair is now complete. Print out a diagram of your belt system. This pulley is attached to a very strong spring and holds the belt tight against the pulleys through its serpentine route around the engine. I changed mine after about 70k miles.
Since this belt is so critical to the operation of your 2003 Altima 2. I didn't have the special tool so I improvised with a 14mm wrench. In it Mod mpe235 gave a tip on how to release the tensioner without a need for tools. I dont think there is a how-to. Title: Changed The Drive Belt on my 02 Altima: Describes the actual replacement and part of the belt. The third generation Nissan Altima, model-years 2002-2006, uses a single serpentine belt to power the alternator, power steering pump, water pump, crankshaft and air conditioning.
Different engines require 2005 Nissan Altima serpentine belt replacement belts of different widths, thicknesses and lengths or circumference. These are prepared for transfer, if you love and wish to take it, simply click save symbol in the web page, and it will be directly downloaded to your laptop computer. I just wanted to add a little word of advice that I never saw in any write-ups. Altima air intake diagram on nissan altima 2 5 cooling system repair guides engine mechanical thermostat autozone altima air intake diagram on nissan altima 2 5 cooling system diagram. Put a wrench on it, and turn it as if you were tightening.
The new belt will need more clearance to get on the pulley. I bought a new serpentine belt for my 2004 2. Here is how to do it: 1 - remove wheel 2 - Remove side plastic cover, behind wheel, by taking off plastic clips 3 - locate the auto tensioner, it has a 14mm bold in the center. As a final point if you need to find unique and recent picture related with 2006 Nissan Altima 2 5 Serpentine Belt Diagram. Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move. If you get confused you can refer back to them when placing the new belt back on.
Insert a screwdriver into the holding boss from rear to front. Once the 05 Nissan Altima serpentine belt replacement is around the tension pulley, release the socket wrench and allow the tension pulley to take up the slack on the Automotive Serpentine Belt Replacement. I didn't have one long enough to really move it and then hold it. After you get the belt on just pull in the same spot again and slide the screwdriver out. The serpentine belt is located on the front of the engine block and winds around several pulleys driving various engine components: water, fuel and power steering pumps, the alternator, air conditioner compressor and possibly other accessories. The hardest part was probably getting that little splash guard back on.
Once the 11 Nissan Altima serpentine belt replacement is around the tension pulley, release the socket wrench and allow the tension pulley to take up the slack on the Automotive Serpentine Belt Replacement. Sep 16, 2011 My sincere apologies for the delayed response. Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley. Move the wrench clockwise to take tension off of the belt. This must be done correctly.
Altima air intake diagram on nissan altima 2 5 cooling system repair guides radiator removal installation autozone altima air intake diagram on nissan altima 2 5 cooling system diagram. Alas I do not have the special tool. A few tips: Use a digital camera to take a few snapshots of the belt in place before you take it off. Altima air intake diagram on nissan altima 2 5 cooling system repair guides radiator removal installation autozone altima air intake diagram on nissan altima 2 5 cooling system diagram. Find the tension pulley located at the bottom of the motor. I have a diagram of the way the belt goes on, and will take a digital picture to be sure I get it right, but is this something I should attempt? The drive belt controls the power steering pump. The original diagram work is managed by Diagrammr.
Again, use the socket wrench to turn the tension pulley far enough so the 11 Nissan Altima serpentine belt replacement can be wrapped around the pulley. Hope helps remember to rate and comment this answer. Take the belt off the pulley and let it hang. The screwdriver you need is a medium sized phillips head, but not too long. Good luck, just get under your car and screw around with it I just got done doing this repair.
Do I need special tools to release the tension? Is there an alternative method? Unfortunately, there wasn't enough room to get a socket onto the belt tensioner, which would have been easier to manage than the wrench. Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley. This must be done correctly. Also read my 2 threads on Page 8 - Altima Forum Title: Need Help In Replacing The Drive Belt. There is a good change the tension pulley will need to be moved farther for the 2011 Nissan Altima serpentine belt replacement because the old belt may have stretched.
If you cannot find it online take a clear picture of the diagram under your hood and print the picture out click image for zoom. Turn the wrench handle, the pulley moves and the tension on the belt slackens. It is awful tight in there. Repair guides engine mechanical ponents accessory drive belts. And please let me know if there's anything else Icould help you with. The video above shows how to check the belts on your 2014 Nissan Altima - if it gives more than a half inch when pressed, is cracked, frayed or appears shiny, you should change it or have it changed immediately.