The doors are adjusted at the hinge attaching loca- 3 Clean the weatherstrip contact surface on the tions on either the body or the door. If the valve body bores, valves, valve body Fig. I downloaded mine so many years ago that I don't recall where I got them from. This will maintain ease of operation 1 Remove the front crossmember cover. Align rear clutch with front annulus gear and install assembly in driving shell.
Be sure spring is completely seated in retainer groove. Then clamp plate and gear assem- bly in vise. Lubricant may be seen dripping from the clutch housing after extended operation. Tag the wires using the marker and masking tape as to their proper locations. If you find that this happens to yours, it will be far less daunting a proposition if you have a service manual in the glove compartment. Use petroleum jelly to washer from annulus gear hub. This Body Repair Manual is prepared for technicians who have attained a high level of skill and experience in repairing collision-damaged vehicles and also use modern service tools and equipment.
Find your 1997 Jeep Wrangler repair manual right now at Chilton. Engage the retainers and side marker wire harness through the access to secure. Remove the mounting bolts from the starter using a socket and ratchet and remove it from the engine. It is currently in its third generation. It was replaced by the Grand Cherokee and it played a significant part in reviving Chrysler's fortunes by moving it into the then nascent market for high-margin sports utility vehicles. Tighten transfer case-to-trans- 1 Remove release bearing and lever from the mission nuts to 35 N·m 26 ft.
The valve The only recommended procedure for flushing cool- check ball is spring loaded and has an opening pres- ers and lines is to use Tool 6906 Cooler Flusher. Inspect the retainer components Fig. Replace worn or damaged parts. Clean all chips from shaft after bushing removal. Reconnect the battery terminal and start the Jeep to test the installation.
All of Chilton's online content for the 1997 Jeep Wrangler is updated monthly, so you'll have the most recent information on hand for any Do-It-Yourself project. Also, verify that all shift 4 Install the 1—2 shift rail into the intermediate plate. On 4 x 4 models, remove both propel- ler shafts. Technicians should refer to both manuals to ensure proper repairs. Enlarged holes tailgate with isopropyl alcohol, or equivalent.
Check press and inspect valve body. Don't waste time calling around to your local bookstores or waiting for a repair manual to arrive by mail. Remove all traces of sealer from the cases and retainers with a scraper and 3M all purpose cleaner. Test One - Transmission In 1 Range Pressure Test Port Locations This test checks pump output, pressure regulation, Pressure test ports locations are provided at the and condition of the rear clutch and servo circuit. Allow the accel- erator to dry for one minute.
To find out if tires are causing the noise or vibra- tion, drive the vehicle over a smooth road at varying speeds. Please read through these instructions and familiarize yourself with them before actually using this manual. Input shaft end play 0. Use a suitably sized press tool to support retainer as close to input shaft as possible. This purges any residual cleaning solvent from the trans- mission cooler and lines. Reconnect the wires according to how you tagged them and tighten the nuts with a wrench. .
Using a 3 Loosen the bolts in the slotted holes Fig. Refer to Group 3, Dif- 2 Remove transfer case. Check for leaks at seal caused by worn seal or burr on converter hub cutting seal , worn bushing, missing oil return, oil in front pump housing or hole plugged. However, there is no need to spend money on a hard copy when you can download one for free direct from this site, and have as many copies of it as you may need for the purposes of fault identification and repair. With valve body in this posi- tion, valve body check balls will remain in place and not fall out when transfer plate is removed. Replace the chain and both sprockets if the chain is stretched, distorted, or if any of the links bind. Jeep Owners Manual is an automobile marque of owned by It is the oldest off-road vehicle brand.
Replace the gear if necessary. If the clutch problem is mission or transfer case, if equipped, components. Check tire pressure frequently when ambient travel, interference with vehicle components may temperature varies widely. A good repair guide is an essential thing to have, for any vehicle. Never attempt this project before completing step 1 or you will put yourself at risk for electrical shock. Flush the case bores and fluid passages thoroughly with solvent.