Let me know if any other photos will help. I am not sure how to post anything other than pics on the forum, so for those who need the diagrams in pdf file format , you will need to provide an email address to send the attachment s to. Fourth: The Metra 2-din install kit is 95-5812, the single din install kit is 99-5812. As you note, you already have 5 wires back there, including electric brakes that blue wire. It will show 0V when the car is off and 0V when the car is on.
With any aftermarket system its going to cost some cash. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. I hate to break out the wire cutters and electrical tape so early in it's life. Anybody tried all this together with a Kenwood unit? Got the wiring and 9000 pounds maximum towing capacity, up from 6000. I am looking for the Harness Side Diagrams for Each I believe on the 05 There are 3 possibly 5 The same may go for the 03 Expy.
If doing front and rear speakers order 2 of these. Find a repair manual for your car - Get instant access to your vehicles drive belt routing, complete wiring diagrams, trouble code information and other available updates and factory bulletins. Sirens produces extremely loud emergency warning tones! I have also tried to get information from 3 different Ford dealers and haven't found any who understand the system. Anyone coverted a flat 4 to 7-wire to include electric brakes, 12v power, and back up lights? I need the wiring schematics to know where they go in the cars. No need to mess with the complete wiring harness that I can see.
If the colors are the same as a 1993 Ford Tempo then the following will work for you. As you note, you already have 5 wires back there, including electric brakes that blue wire. However, the double din doesn't fit in our new 2007 expeditions out of the box. Does anyone know how hard it would be to install the 7 pin harness? If you can come up with an O7 Expedition Pinout as well that would be great!! I have a indash monitor I removed from 04' I just have to sell it. Unplug all the connectors and remove the dash bezel. Unfortunately, Alldata doesn't let you copy, paste, save to file, etc. A standard aftermarket radio uses 12v which will cause a loud pop when the amp turns on or off.
Nothing too difficult here except to note that the steering wheel control wire is pin 18 in the 24 pin connector. Check other posts, here and elsewhere. Make sure to grab the appropriate tools to test all the wires in your Explorer. Sorry I don't have any pictures, but I hope that helps out. Once that is removed you can remove the trim around the radio by pulling forcefully from the bottom and working your way up.
GuruY62Q4 answered 11 months ago Can someone update this with color diagram for 2003 expedition please i made a dummy move and cut the factory plugins that the wires connect to off because my dvd navigation came with wiring harness which had split wires on it and i thought they all matched to my disappointment i found i gotta big problem and no radio still. If you head down to one of the local parts stores ask them if they have a copy of one. This schematic is provided free of charge and may not be 100% accurate. Few trailers have backup lights and trailer battery charge is at most a trickle under one amp charge anyway. Unfortunately theres just not enough to work with to make a 4 to a 7 pin.
Then pop that panel unplug any electrical connectors and remove it. Here is the audio stereo radio wiring information for your 2007 Ford Explorer with the standard or amplified systems. I do not want to be directed to a check here its only 24. The Modified Life staff has taken all its Ford Expedition car radio wiring diagrams, Ford Expedition car audio wiring diagrams, Ford Expedition car stereo wiring diagrams, Ford Expedition car radio wiring schematics, Ford Expedition car wiring diagrams and cataloged them online for use by our visitors for free. I can give ya a hand here, either you go to a dealer and pay fairly hefty for them to do it, or I can give ya some schematics for it and you go to work. The wiper motor is easier You can then route the wire back into the cabin through any of the firewall grommets.
To Submit a request for basic free wiring diagrams , As this is a free service it receives an overwhelming amount of requests and may take up to a week or longer for a response. If the label on the harness is visible, could you post the part number??? This will insure the ability to read the free wiring diagrams with ease. There are no screws holding that panel on. Are you sure about this? Just submit a request for the wiring diagram you want ex. Those are great if you are hooking up a stereo and bought adapter plugs, this is available on the package of the plug. As far as I can tell each stereo option for the Aerostar had a different wiring harness.
I'm not a big fan of others working on my vehicles and the more I look into this issue, the more I'm convinced this 4- to 7-wire conversion is going to require me running the necessary wires to the bumper. Unfortunately, I can't remember exactly where it is located From my own experience, I soldered all the connections from the new radio to the metra harness and that took a while, but was worth it. You simply remove the plastic boot on the connector and it is exactly like a standard xm antenna connector. Each Diagram has to be hand selected and sent. You simply connect the wires from the Metra to your new radio and then plug the metra connectors into the factory connectors. Keep in mind if you are installing a new radio you need the radio removal keys, the wiring harness, the antenna adapter, and the mounting kit as well. They plug right in then right on to the new speaker making installation a breeze.
All information is provided as-is and accuracy is not guaranteed. Some european wiring diagrams are available also. You can send the email address to me via my user profile I think - just add me as a friend via the cp. When the park lamps are turned off, voltage is no longer applied to the Radio, and the display brightens. If so it will not work if you remove the head unit for it. The rear tabs hit the metal bracing of the center console, so you'll have to cut them off.